MOTUnation.com

Hi, I just started using an m-audio Project Mix I/O as a firewire-based control surface with Digital Performer. I'm liking it a lot but have a couple of question/concerns. The plugin button (on the PMIO) only lets me change which plugin is in a selected slot in DP but control their knobs/parameters ...

I'm probably missing something really simple but when I configure a 2408mkII to enable ADAT banks A and B and plug my O2R's 1st ADAT card into bank A on the 2408 and the O2R's 2nd ADAT card into bank B, I can hear the 2408's ADAT outputs through my board's tape returns but can't get a signal into th...

After upgrading my PPC Mac to a Power Mac, I'm a little confused about plug-in formats and compatibility(s). My hardware does/will consist of MOTU PCIe-424 and a couple of 2408's and an M-Audio Project Mix I/O. I've used Digital Performer 5.13 for quite a while but have Protools 9 on order. I instal...

Hi,

When I upgrade my pcix-424 to a pcie-424 through MOTU,
will I be able to keep my pcix-424 card?

Thanks,

Jon

In DP 5.13, why would normalize be gray'd out after I
select a soundbit and go to the audio menu?

Thanks,

Jon

Are there any control surfaces besides the Tascam 1884
that have 8 mic pre/line inputs and ADAT inputs as well
that work well with DP?

I like the Tascam but have seen reports of compatibility issues
with PT.

Thanks,

Jon

I'm using a Profire Lightbridge and Digital Peformer to record a test track via any of my preamp devices with ADAT out. All I get is an awful vocoder type signal on the track. Playback works just fine with no clicks and pops etc... I don't believe this is a wordclock problem because of the good play...

Hi,

Does anyone know if a PCI-424 (with 2408's attached)
can coexist with an M-audio lightbridge with both
used (not at the same time) with DP?

Thanks,

Jon

I'm sure you've all heard this problem a million times but I can't seem to get past it. I'm running a Mac G4 700mhz, OSX 10.4.10, 1.2gb ram, PCI424, 2408mkIIs, and DP 5.12. DP is regularly hanging and crashing on me. I can't even get through a mix of 10 audio tracks without plug-ins. After the crash...

pci drivers 1.1.0

After upgrading to OSX 10.4.8, PCI drivers 1.0.8, DP 4.61 on a G4 733 system with PCI-424 and two 2408 mkIIs, the CPU pegs every now and then during recording/playback causing audio glitches that scare my clients (and me). They don't seem to affect the tracks themselves but I'm wondering how I might...

ello, I run a PCI-424/2408mkII/Mac G4 733/DP4.61 system which worked great under OSX 10.2.6. When I upgraded to 10.4.6 I started getting playback glitches (the CPU monitor idles at a very low level and then occasionally redlines quickly then drops back down, The audio playback glitch happens as the ...

Hi, I was running my DP 4.52 system on a Mac G4 OSX 10.2.6 with PCI-424 and two 2408mk2s. Today I upgraded to OSX 10.4.6 I also upgraded to the current pcix_1.1.0 PCI driver. The PCI audio console and CueMix consoles both started up fine and seemed to work fine. When I started DP 4.52, it scanned my...

Hi, Whether I'm running DP or not any input I make on the digital inputs of my 2408 get's echo'd to the digital output channels 1-2. I've worked with the PCI-424 Hardware Setup and the CueMix setup control programs (I'm on a Mac) and I'm unable to stop this with either of them. Any ideas? Thanks, Jon