MOTUnation.com

....and don't understand it. It's seriously unwieldy. 12 knobs to set individually on a stereo source rather than a linked 6 pair!

EMRR wrote: ↑Thu Apr 13, 2023 7:21 pm ....and don't understand it. It's seriously unwieldy. 12 knobs to set individually on a stereo source rather than a linked 6 pair!

I know! It's great gate, but this is a serious oversight in its implementation.

EMRR wrote: ↑Thu Apr 13, 2023 7:21 pm ....and don't understand it. It's seriously unwieldy. 12 knobs to set individually on a stereo source rather than a linked 6 pair!

There's a way to join stereo parameters... I think you must press Option (or is it control?) as you adjust them, and some parameters will be linked on both sides.

Thanks FM!

Yes, the Option key will link the controls, and Command is for more fine-tuned adjustments. You can press them both down at the same time to make fine-tuned adjustments to left and right simultaneously.

Thanks again gents. Of course, this is good info, but a Stereo Link button on the plugin would be awfully nice, too.

Tritonemusic wrote: ↑Fri Apr 14, 2023 8:34 am Yes, the Option key will link the controls, and Command is for more fine-tuned adjustments. You can press them both down at the same time to make fine-tuned adjustments to left and right simultaneously.

That does not work here in DP11.22. I went through every control/option/command/+shift combo and nada. Please explain more.

EMRR wrote: ↑Fri Apr 14, 2023 10:40 am

Tritonemusic wrote: ↑Fri Apr 14, 2023 8:34 am Yes, the Option key will link the controls, and Command is for more fine-tuned adjustments. You can press them both down at the same time to make fine-tuned adjustments to left and right simultaneously.

That does not work here in DP11.22. I went through every control/option/command/+shift combo and nada. Please explain more.

All I did was follow the Digital Performer Plug-ins Guide. These are screenshots from there, and it works just as written (but I'm still on DP10.13...not sure if anything has changed since then).




When I hold them BOTH down at the same time, it does what I'd expect; Stereo control with fine-tune adjustments.

I hope that made sense.

EMRR wrote: ↑Fri Apr 14, 2023 10:40 am

Tritonemusic wrote: ↑Fri Apr 14, 2023 8:34 am Yes, the Option key will link the controls, and Command is for more fine-tuned adjustments. You can press them both down at the same time to make fine-tuned adjustments to left and right simultaneously.

That does not work here in DP11.22. I went through every control/option/command/+shift combo and nada. Please explain more.

Ditto The manual says the option key works, but here, no key combo works.

Tritonemusic wrote: ↑Fri Apr 14, 2023 11:02 am

EMRR wrote: ↑Fri Apr 14, 2023 10:40 am

Tritonemusic wrote: ↑Fri Apr 14, 2023 8:34 am Yes, the Option key will link the controls, and Command is for more fine-tuned adjustments. You can press them both down at the same time to make fine-tuned adjustments to left and right simultaneously.

That does not work here in DP11.22. I went through every control/option/command/+shift combo and nada. Please explain more.

All I did was follow the Digital Performer Plug-ins Guide. These are screenshots from there, and it works just as written (but I'm still on DP10.13...not sure if anything has changed since then).

When I hold them BOTH down at the same time, it does what I'd expect; Stereo control with fine-tune adjustments.

I hope that made sense.

Thanks.....just doesn't work here. Didn't in DP8 either.

Well, that is weird, guys. I tested it before posting, and tested it again. It still works for me. I wish I could help you figure this out.

Here's a question:

Does holding down Command while changing parameters on any stock DP plug-in make a difference, as far as fine-tuning is concerned?

yes, Command works for fine turning.

Tritonemusic wrote: ↑Fri Apr 14, 2023 2:07 pm Well, that is weird, guys. I tested it before posting, and tested it again. It still works for me. I wish I could help you figure this out.

Here's a question:

Does holding down Command while changing parameters on any stock DP plug-in make a difference, as far as fine-tuning is concerned?

Yes, command has always worked for me. I use that all the time.

I noticed option (to link channels) not working a year or s ago) to motu tech support, they confirmed and like lots of other confirmed bugs its still broken......

pencilina wrote: ↑Fri Apr 14, 2023 6:44 pm I noticed option (to link channels) not working a year or s ago) to motu tech support, they confirmed and like lots of other confirmed bugs its still broken......

Thanks for the the info, pencilina. I guess that explains why mine's still working (DP 10.13).