BX8 monitor setup questions

Here's where to talk about preamps, cables, microphones, monitors, etc.

Moderator: James Steele

Forum rules
Here's where to talk about preamps, cables, microphones, monitors, etc.
Post Reply
User avatar
Timeline
Posts: 4910
Joined: Tue Nov 09, 2004 10:01 pm
Primary DAW OS: MacOS
Location: Fort Atkinson Hebron, Wisconsin...
Contact:

BX8 monitor setup questions

Post by Timeline »

OK I know this sounds kind of lo Fi but I sold my big DynAudio Munro monitors because I have to move in a few months and I couldn't even lift them. Sad really.

Anyway.... Now, I have these cheap little BX8 monitors left and I have placed them on an open platform above me slanting down sort of like on shelves. When I set the controls to flat my mixes sound bright and without lo end and little lower mids. I just need to know what the best switch selection for realistic pro monitor tone on these might be as they have a three position field effect switch which changes the sound quite a bit.

I probably need subs I would think too but a sub that would keep up with a pair of 8" woofers. Please advise for best sound.
User avatar
BradLyons
Posts: 2635
Joined: Sun Oct 24, 2004 10:01 pm
Primary DAW OS: Windows
Location: Atlanta, GA
Contact:

Re: BX8 monitor setup questions

Post by BradLyons »

Sounds like it's phase cancellation from standing waves. Turn up the bass until you like it, then burn a CD and go listen to it in your car. If the bass is boomy there, then that's your answer.
Thank you,
Brad Lyons
db AUDIO & VIDEO
-Systems Advisor, CTS
User avatar
Timeline
Posts: 4910
Joined: Tue Nov 09, 2004 10:01 pm
Primary DAW OS: MacOS
Location: Fort Atkinson Hebron, Wisconsin...
Contact:

Re: BX8 monitor setup questions

Post by Timeline »

Thanks but it's not phase. I would recognize that immediately.
It's positioning but I don't have the manual any more so i need to know the correct position of the enhancement switch.

thanks
User avatar
BradLyons
Posts: 2635
Joined: Sun Oct 24, 2004 10:01 pm
Primary DAW OS: Windows
Location: Atlanta, GA
Contact:

Re: BX8 monitor setup questions

Post by BradLyons »

............and those switches are there to adjust for phase cancellation due to standing waves, full-space....half-space....etc. :roll:
Thank you,
Brad Lyons
db AUDIO & VIDEO
-Systems Advisor, CTS
User avatar
jon
Posts: 233
Joined: Sat Oct 16, 2004 10:01 pm
Primary DAW OS: MacOS
Location: Here
Contact:

Re: BX8 monitor setup questions

Post by jon »

Timeline wrote:OK I know this sounds kind of lo Fi but I sold my big DynAudio Munro monitors because I have to move in a few months and I couldn't even lift them. Sad really.

Anyway.... Now, I have these cheap little BX8 monitors left and I have placed them on an open platform above me slanting down sort of like on shelves. When I set the controls to flat my mixes sound bright and without lo end and little lower mids. I just need to know what the best switch selection for realistic pro monitor tone on these might be as they have a three position field effect switch which changes the sound quite a bit.

I probably need subs I would think too but a sub that would keep up with a pair of 8" woofers. Please advise for best sound.
I have a pair at work and they are far from little.
MAC PRO 2x2.26 / OSX 10.7.2 & 6 GB RAM., POWERMAC G5 2x2. / OSX 10.5.9 & 4 GB RAM., MAC BOOK 2.0 / OSX 10.7.2 & 2GB RAM.,DP 7.24, Logic Pro, Motu 896mk3, Lynx Aurora 8, Motu Ultralite Mk3, UAD-2 6.1.0, Mackie Onyx 800R, V-Drums.
Post Reply