Masterworks Gate has no linked controls for stereo? I forget this over and over....

[EMRR]

....and don't understand it. It's seriously unwieldy. 12 knobs to set individually on a stereo source rather than a linked 6 pair!

[HCMarkus]

....and don't understand it. It's seriously unwieldy. 12 knobs to set individually on a stereo source rather than a linked 6 pair!

I know! It's great gate, but this is a serious oversight in its implementation.

[FMiguelez]

....and don't understand it. It's seriously unwieldy. 12 knobs to set individually on a stereo source rather than a linked 6 pair!

There's a way to join stereo parameters... I think you must press Option (or is it control?) as you adjust them, and some parameters will be linked on both sides.

[HCMarkus]

Thanks FM!

[Tritonemusic]

Yes, the Option key will link the controls, and Command is for more fine-tuned adjustments. You can press them both down at the same time to make fine-tuned adjustments to left and right simultaneously.

[HCMarkus]

Thanks again gents. Of course, this is good info, but a Stereo Link button on the plugin would be awfully nice, too.

[EMRR]

Yes, the Option key will link the controls, and Command is for more fine-tuned adjustments. You can press them both down at the same time to make fine-tuned adjustments to left and right simultaneously.

That does not work here in DP11.22. I went through every control/option/command/+shift combo and nada. Please explain more.

[Tritonemusic]

Yes, the Option key will link the controls, and Command is for more fine-tuned adjustments. You can press them both down at the same time to make fine-tuned adjustments to left and right simultaneously.

That does not work here in DP11.22. I went through every control/option/command/+shift combo and nada. Please explain more.

All I did was follow the Digital Performer Plug-ins Guide. These are screenshots from there, and it works just as written (but I'm still on DP10.13...not sure if anything has changed since then).

Screen Shot 2023-04-14 at 12.53.08 PM.png (95.6 KiB) Viewed 959 times

Screen Shot 2023-04-14 at 12.55.21 PM.png (36.68 KiB) Viewed 959 times

When I hold them BOTH down at the same time, it does what I'd expect; Stereo control with fine-tune adjustments.

I hope that made sense.

[bayswater]

Yes, the Option key will link the controls, and Command is for more fine-tuned adjustments. You can press them both down at the same time to make fine-tuned adjustments to left and right simultaneously.

That does not work here in DP11.22. I went through every control/option/command/+shift combo and nada. Please explain more.

Ditto The manual says the option key works, but here, no key combo works.

[EMRR]

Yes, the Option key will link the controls, and Command is for more fine-tuned adjustments. You can press them both down at the same time to make fine-tuned adjustments to left and right simultaneously.

That does not work here in DP11.22. I went through every control/option/command/+shift combo and nada. Please explain more.

All I did was follow the Digital Performer Plug-ins Guide. These are screenshots from there, and it works just as written (but I'm still on DP10.13...not sure if anything has changed since then).

When I hold them BOTH down at the same time, it does what I'd expect; Stereo control with fine-tune adjustments.

I hope that made sense.

Thanks.....just doesn't work here. Didn't in DP8 either.

[Tritonemusic]

Well, that is weird, guys. I tested it before posting, and tested it again. It still works for me. I wish I could help you figure this out.

Here's a question:

Does holding down Command while changing parameters on any stock DP plug-in make a difference, as far as fine-tuning is concerned?

[bayswater]

yes, Command works for fine turning.

[EMRR]

Well, that is weird, guys. I tested it before posting, and tested it again. It still works for me. I wish I could help you figure this out.

Here's a question:

Does holding down Command while changing parameters on any stock DP plug-in make a difference, as far as fine-tuning is concerned?

Yes, command has always worked for me. I use that all the time.

[pencilina]

I noticed option (to link channels) not working a year or s ago) to motu tech support, they confirmed and like lots of other confirmed bugs its still broken......

[Tritonemusic]

I noticed option (to link channels) not working a year or s ago) to motu tech support, they confirmed and like lots of other confirmed bugs its still broken......

Thanks for the the info, pencilina. I guess that explains why mine's still working (DP 10.13).