MOTUnation.com

OK. Your interface is connected and detected in both MOTU Audio Setup.app and Audio MIDI Setup.ap p, right? Start Console in your Utilities Folder. This should tell you if a) a library is trying to load but can't or b) if something is trying to load that shouldn't. The lines can be expanded if nece...

Yes it's detected and works normally! I'm going to try your hint this evening, opening Console to find out what's happening... It's strange because I've also tried to modify parameters on the hardware (for example MUTE ON/OFF, PAN, FADERS) and each time I launched CueMix FX it showed those changes b...

Hi everyone! This problem is giving me headaches! I have an Ultralite mk3 and I can't use anymore Cuemix FX, I don't know why! Every time I launch the app it starts in not responding status, with the colored spin ball... I've uninstalled and re-installed everything (manually removing kexts and prefe...

Hi everyone! since I've upgraded to OS X Mavericks (fresh install of 10.9.2, updated to10.9.4), I'm experiencing audio drops during everyday use of my machine. In particular, my Ultralite goes silent when I open/close every app, Safari tabs, change folders in Finder and some times without doing anyt...

You wouldn't want to use any analog for loopback operations due to the fact it's analog and there would be a loss in signal. For example: Degradation. S/PDIF is fine to use because it is completely digital. For example: Never any loss. You're absolutely right! I think I'll buy a digital cable (I ne...

I have done and it works great! Just the way I told before. why to buy a crossover when you have CUEmix! ;) simply using the eq parameters I've got a cut on 120 Hz: in the mix called "monitors" (the outs to the monitors) I've cut away almost everything under 120 Hz (at 120 starts to go dow...

I will use a Y cable (two jacks and a mini-jack) to link the out pair assigned to a mix with the sub and the width to 0 for the channel in that mix. this way (width 0.00) i will have it to mono, right? I will not use the satellites of the sub, but a pair of monitor, so I need different out to use al...

If the subwoofer has stereo ins and a low pass filter and the satellites a built-in high-pass filter, I'd recommend simply splitting the L and R main outs to feed both the sub and respective satellite. Or pass thru the sub if the system has a built-in crossover network. I'm not going to use a 2.1 s...

Great ! for other readers whom might be interested, i´ve found a quick way for sending windows output to 2 stereo pairs. Setting the windows out to 3/4 an then selecting 3/4 on the main out assign in motu audio console, so 1/2 replicates them. I was searching exactly a solution for the same questio...

Thanks NazRat! I think this is the same situation: http://www.motunation.com/forum/viewtopic.php?f=14&t=49656&p=420782&hilit=loopback#p420839 I tried what zombiesound wrote at the end, but it doesn't work (or I have made a mistake) so I think I will use the method I had tought, maybe usi...

thanks torrentg for your answer! I think it will not work for me. I didn't said that in windows, I use Motu Main Out 1-2 as device for the audio (Sorry, I didn't said it before). so if I use main out, only from them I get the sound. Can I split audio from PC to different outputs? I know I can do it ...

Hi you all! I'm wondering if it's possible to use 2 monitors plus a sub woofer (from a former 2.1 system) with my UltraLite. I would like to try because my girlfriend is going to dump her old 2.1 because the monitors are gone... but the sub is still working. I tought that i can set main outs as audi...