MOTUnation.com

Thanks for your input! I've found that BTD can process more tracks as well as other VIs and plugins than mixing in real time. It would be nice if DP notified of any processing errors during BTD like it does when you play/mix in real time. I advised MOTU to include this feature in their next update. ...

Does Bounce To Disk allow you to process more tracks, VIs and effects than mixing in real time with DP 9.52? I have a large mix which is triggering error messages and causing a lot of clicks during playback because the CPU is overloaded. But when I bounce the entire mix, I get no error messages and ...

An update to this thread... The meters peaking in DP for this master was due to misinformation from the mastering engineer and incompetence. First, the mastering engineer advised me that his meters were not peaking in Pro Tools whereas they were in DP. When I had Massey, the software developer of th...

Doug

If so, please post the link.

Thanks!

I have a screenshot which shows the discrepancy between the meters and the Trim plugin.

But I don't know how to display it on this site.

This mastered file is formatted at 96K / 32 Bit Float, wav. Though the meters read in excess of +5db above 0db, I don't hear any distortion or clipping. Is it plausible, at this high level of resolution and dynamic range, that the audio file is not distorting and therefore acceptable to be converted...

Thanks for your replies! I conferred with Massey regarding their L2007 Brickwall Limiter and they stated no level should exceed 0db. In fact, they limit just a hair below 0db to avoid any misreading on the meters according to them. They were kind enough to master a segment of this same song. When I ...

Just mastered a song on a Pro Tools system with the Massey L2007 Brickwall Limiter. Burned the mastered song to CD. All levels in both formats and systems look fine. No peaking on any meters. When I import this same mastered song into DP 9.52, the meters peak constantly. Though I hear no distortion ...

Hi Arum Typically anywhere between 512 and 2048... It's just backing tracks playing with no plugins, VIs or automation which should be more than adequate for the processor to record one vocal track. My belief is the MOTU AD converter has trouble accurately interpreting the ultrasonic range. There's ...

...hoping to avoid any pitfalls

Any insight would be greatly appreciated...

Thanks,
Gallospole

I've been experiencing audio clicks from time to time with my 828 MK3 when recording vocals through my Neve 73 EQ while boosting 10K to 20K by 2 to 4 db. In addition, at least half the time, the pitch automation is not read properly in DP. When I remove the 10K to 20K boost, it reads pitch perfectly...

Dave All the best! Read your book...very resourceful...spoke to you on the phone a few times...very patient...most of the time you could've rightfully told me to RTFM...you served MOTU and its community very well throughout the years! Thanks again! Best regards, Gallospole aka Marc A Gallo, Mind The...

Andrew was helpful at MOTU.

Apparently our output faders were down within the MOTU Audio Setup program.

Always something stupid!

But it would be nice if this same function was available in CueMix which is the monitoring program we typically use.

Gallospole

I have two workstations operating at OS 10.9.5 & 10.11.6 respectively. The Hardware Insert works fine in 10.11.6 but fails to pass any audio in 10.9.5. Using DP 9.12 and their 828 MK3 interface. In addition, I can't even pass audio externally using any of their analog outputs like Analog 1, 2, e...

Thanks Kurt

But after further tests, I believe it's a buggy DP file.

I'm going to attempt to rebuild the project in a new file and hopefully correct this issue.

Time consuming and frustrating… posting.php?mode=reply&f=1&t=61980#