MOTUnation.com

Unfortunately no. I have come across this problem many times. I have just found work arounds. DP can get confused and overloaded very easily. I work at 96k, which is hard on CPUs. But this problem has nothing to do with that. CPU is running at about 65%. I have found a way to deal with it because I ...

Hi all. I have had this problem many times, but because I usually print through outboard to a second computer, I rarely have to deal with it. Right now, I have to print the final mix in DP, and when I add a stereo track and try to assign the mix buss as the input, the spinning wheel of death starts,...

Hi all. I get the feeling there is no way around this. With say TDR Nova, Digital Performer will not record automation if you want to turn the HP filter on and off. I was going to email TDR, then I thought, better check this. So I loaded up another DAW which I use, Re@per, and it turns out that that...

MOTU have no idea what the problem is. I have tried a lot of things. Getting rid of plugins just in case that was the problem etc.

I will continue to record audio via an aux channel and manually nudge.

I will also continue to investigate for a solution.

Thanks for everyone's suggestions.

Hi Dave. I appreciate your input. And I appreciate the fact that this is a difficult concept to write clearly about. I have really tried to write clearly. But it would appear, not clearly enough. I will wait for MOTU's tech response. For now, my work around is working fine by tricking DP into thinki...

Hi Dave. It's not outside the box, as I monitor two hardware parallel drum bus comps right up until the mix is complete. Then print. My monitoring chain is always set up with a 8136 sample delay. If it ever changed, even by only 5 to 10 samples, the drums would go out of phase and sound ridiculous. ...

Thanks Dave. I understand this. The true offset is 8136 samples. That's what has to be set up when I am monitoring parallel hardware processing. But when it is printed, DP tries to allow for latency and prints as close to correct as it can. At the moment, it is not consistent. I have done what you d...

I am. And it's really bad. I have checked this morning and it's not the plugin latency button. I would have never touched that. I have sent a technical request to MOTU. There is a work around, but it's laborious. You use a track to bring in the audio and then send it out via a bus to a second audio ...

I've just realised, turning off delay compensation must muck up plugin latency. I'll have to mess around with it.

Thanks for the replies. I have been over every parameter. And yes, I have a feeling, when I first started using DP, I unchecked the plugin delay compensation. For years I manually nudged recordings. Then I remember finding "in-out fine tuning", and didn't have to manually nudge anymore. I ...

Hi all. When I first started using DP, 5.6 I think, I needed to nudge any takes to make up for the round trip latency. Somewhere a long the line it became automatic. But I'm finding it's not consistent or reliable. I want to be able to turn off the automatic latency correction of recorded audio. I w...

Hi all. I have a problem with the hardware setup offset fine tuning. My sample offset is 8136 samples for the round loop when recording audio. But last week, when using parallel outboard drum compression, the audio was in time/phase when I was using it just on the input(live), but when I printed it,...

Not the answer I was after. But thanks anyway.

Spig

Hi all. Is there a way to “show/hide” tracks for both the sequence editor and the mixing board? I can only select to “show/hide” tracks for each individually. I would much rather be able to select the tracks I want to see in the track selector globally. Rather than have to select for the sequence ed...

Not thick headed. 2nd computer because the the Lyra and the Aurora don't sound good clocked off each other. Syncing because it saves a whole lot of time when you use different parts of different master takes. At the moment, I have to time align everything manually. I would much prefer they were alig...